Get 2024 Free Cisco 300-615 Exam Practice Materials Collection [Q97-Q120]

ExamBoosts December 16, 2024 300-615 > Cisco 0

Rate this post

Get 2024 Free Cisco 300-615 Exam Practice Materials Collection

Get Latest and 100% Accurate 300-615 Exam Questions

The Troubleshooting Cisco Data Center Infrastructure certification exam is intended for IT professionals with experience in implementing and troubleshooting Cisco data center technologies. 300-615 exam requires a deep understanding of various Cisco data center technologies, such as Cisco ACI, Cisco UCS, and Cisco NX-OS. 300-615 exam consists of multiple-choice questions, simulations, and drag-and-drop questions. Successful completion of the exam leads to the Cisco Certified Specialist – Data Center Operations certification, which is a valuable asset for IT professionals looking to advance their careers in the field of data center technologies.

QUESTION 97
Refer to the exhibit. The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?

VSAN 1 is suspended.

The SFP is unsupported.

Trunk mode must be activated.

The interface is in an incorrect mode.

The interface VSAN is deleted or is in a suspended state.
To make the interface operational, assign that port to a configured and active VSAN.
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/san_switching/421_n1_1/b_Cisco_n5k_nxos_sanswitching_config_guide_rel421_n1_1/Cisco_n5k_nxos_sanswitching_ config_guide_rel421_n1_1_chapter3.html

QUESTION 98
The external routes fail to propagate to leaf switches in Cisco ACI fabric.
Which two actions resolve the issue? (Choose two.)

Configure an MP-BGP area.

Associate the correct contract to the L30ut.

Specify the spine nodes as route reflectors

Assign an MP-BGP AS number to the fabric.

Enable the VTEP pool in the fabric

QUESTION 99
Refer to the exhibit.

A network engineer notices packet drops on FCoE traffic from the servers. Which action resolves the issue?

Apply flowcontrol receive on the interface.

Apply flowcontrol transmit on the interface.

Enable priority flow control on the interface.

Disable priority flow control on the interface.

QUESTION 100
Refer to the exhibit. A functioning trunk port Ethernet1/48 exists between two identical Cisco Nexus 5000 Series Switches. The interfaces on the switches support the MACsec feature and are configured identically. To enable manual MACsec, an engineer adds the configuration shown in the exhibit to both sides of the trunk. The trunk port stops functioning. Which action should be taken to resolve the issue?

Disable and then enable the port

Enable the license for the trunk ports to support MACsec

Lower the MTU value to less than 9216 bytes

Configure the PMK with a length of 2048 bytes

QUESTION 101
Refer to the exhibit. A blade that is connected to FI-A fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA0 as the SAN Primary. Which action resolves the issue?

Change Adapter Policy to VMWare on vHBA0

Change vHBA0 to VSAN 11 in Service Profile

Configure vHBA_SAN_A zone to VSAN 10

Set VSAN to 11 in vHBA_SAN_

QUESTION 102
Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?

Reset the error packet counter

Configure the hello timer to match the neighbor

Configure the FSPF dead interval with a value higher than 80 seconds

Reset the inactivity timer on switch-2

Reference:
https://www.cisco.com/en/US/docs/switches/datacenter/nexus5500/sw/troubleshooting/guide/n5500_ts_sans.html

QUESTION 103
Refer to the exhibit. An engineer performs a POST operation using REST API on the Cisco Nexus switch to retrieve a managed object, but the operation fails. Which configuration resolves the issue?

https://172.16.10.1/api/node/mo/uni/tn-Test1.xml?rsp-subtree=full&rsp-prop-include=config-only

icurl-k-v https://172.16.10.1/api/node/mo/uni/tn-Test1.xml?rsp-subtree=modified=config-only

https:/172.16.10.1/api/node/mo/uni/tn-Test1.xml?rsp-subtree=modified=config-only

icurl-k-v https://172.16.10.1/api/mo/uni.xml?rsp-subtree=no<fvTenantname=”Test1″/>

QUESTION 104
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)

Equipment FSM page, InternalBackup stage

Service profiles page, InternalBackup stage

Admin page, PollInternalBackup stage

Equipment FSM page, PollInternalBackup stage

Admin page, InternalBackup stage.

QUESTION 105
Refer to the exhibit.

The integration between Cisco UCS Manager and Cisco UCS Central failed. Which action resolves the issue?

Implement the consistent NTP source between the appliances

Implement the connectivity between the appliances through a firewall

Configure the certificate between the appliances

Configure the shared secret key between the appliances

QUESTION 106
Refer to the exhibit.

The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?

Reconfigure the initiator and the target to be in the same zones.

Reactivate the zoneset.

Reset the port for FC ID 0x970102 and FC ID 0x970200 to log in to the fabric.

Reset the port for FC ID 0x970209 and FC ID 0x9700c2 to log in to the fabric.

QUESTION 107
Refer to the exhibit.

An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

Set the local group number as 300 in the remote data center configuration

Run version 1 and version 2 HSRP on VLAN300 in the local data center.

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

Explanation
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp_fhrp/configuration/xe-16/fhp-xe-16-book/fhp-hsrp-v2.p

QUESTION 108
Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

Reconfigure the Drive Type from “Removable” to “Non-Removable”

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to “Auto”

QUESTION 109
Refer to the exhibit.

An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?

The interface is working correctly and fully operational, but it is not in use.

The interface policy is misconfigured.

“out-of-service” is the default interface status in ACI.

“out-of-service” indicates that no service graph is in use for this interface.

QUESTION 110
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?

Install Infrastructure Firmware, then Install Server Firmware.

Install infrastructure Firmware, then Install Hypervisor Firmware.

Install Hypervisor Firmware, then Install Infrastructure Firmware

Install Server Firmware, then Install Infrastructure Firmware

Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-5/b_GUI_Firmware_Ma

QUESTION 111
Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb FC.

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

QUESTION 112
Refer to the exhibit.

A web browser displays a “not secure” warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?

Load third-party certificate to UCS Manager.

Use the correct TCP port for HTTPS.

Use a supported web browser.

Use a supported version of UCS Manager.

QUESTION 113
Refer to the exhibit.

A blade that is connected to FI-B fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA1 as the SAN Primary. Which set of actions resolves the issue?

* Set ESX01_B zone to VSAN 20.
* Create a new vHBA and assign VSAN 20.

* vHBA1 to VSAN 20 in Service Profile.
* VMware Adapter Policy on vHBA1.

*Apply VMware Adapter Policy on vHBA1
*Change vHBA1 to VSAN 20 in Service Profile

* Set ESX01_B zone to VSAN 20.
* Change vHBA1 to VSAN 20 in Service Profile

QUESTION 114
Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Explanation
Need exact snap shot to confirm the following.
The selection of is due to
* SNMP command has the key word “oid”.
* The command “switchto vdc Core” show run in “enable” mode, not “config t” mode.

QUESTION 115
Refer to the exhibit.

An engineer is troubleshooting the connectivity between Server-1 and Server-2. Which action resolves the connectivity issue?

Enable BGP advertise pip feature on both leaf switches

Configure the same source IP address on NVE and virtual peer link on leaf switches

Classify CFS messages for strict priority queue on spine switches

Change all ports on spine switches as port-type fabric

QUESTION 116
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

Verify that the SFPs are supported.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.

Run the shutdown and then no shutdown command on the interface.

Run the switchport ignore bit-errors command on the interface.

QUESTION 117

Refer to the exhibit. A network engineer creates an EEM script to trigger an SNMP notification when a user enters configuration mode, but the trap is not received when the condition is met. Which action resolves the issue?

Append action 2.0 event-default to the script

Append action 2.0 cli “conf t” to the script

Modify snmp-trap strdata “Configuration changed” to syslog msg Configuration changed

Modify cli match “conf t” to “snmp match “conf t”

QUESTION 118
Refer to the exhibit. The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs.
Which configuration set must be added to the script to fix the issue?

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry- val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry- val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Need exact snap shot to confirm the following.
The selection of is due to
SNMP command has the key word “oid”.
The command “switchto vdc Core” show run in “enable” mode, not “config t” mode.

QUESTION 119
Refer to the exhibit.

The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?

event statement

event-default action statement

policy-default action statement

IP address of the SNMP server

QUESTION 120
Refer to the exhibit. Partial configuration from N9K-1 and N9K-2 is included. The client has two WANs connected.
WAN-1 is for normal business-day activities.
WAN-2 is for server backups during nonworking hours of 1:00 a.m. to 5:00 a.m. daily.
The client says that at the scheduled time for backup, the data center server failed to use the WAN-2 link to back up the servers to the cloud backup system. What is the solution to this problem?

The event timer must be written in epoch time format.

The Cisco Nexus switch must be configured with one applet because a configuration with two applets will fail.

The Cron entry must be configured without double quotes.

The applet called “Backup” must include an action to remove the current static route.

Loading …

Cisco 300-615 (Troubleshooting Cisco Data Center Infrastructure) Certification Exam is designed for IT professionals who wish to demonstrate their skills in troubleshooting complex data center infrastructure issues. Troubleshooting Cisco Data Center Infrastructure certification exam is part of the Cisco Certified Specialist – Data Center Operations certification track and validates an individual’s knowledge and skills in identifying and resolving problems related to Cisco data center infrastructure technologies.

Maximum Grades By Making ready With 300-615 Dumps: https://www.examboosts.com/Cisco/300-615-practice-exam-dumps.html