SolarWinds SPM-NPM Questions and Answers Guarantee you Oass the Test Easily [Q35-Q55]

ExamBoosts September 28, 2023 SPM-NPM > SolarWinds 0

Rate this post

SolarWinds SPM-NPM Questions and Answers Guarantee you Oass the Test Easily

Share Latest SPM-NPM DUMP with 77 Questions and Answers

QUESTION 35
What is the average resource consumption of an agent?

Less than 1% CPU, no storage because the agent is 1% in memory for faster access

Between 1-2% CPU if the bandwidth is less than 8 KB/s

Less than 1% CPU, max 1 MB of memory, 1 MB storage

Agents run as a virtual process and do not require local resources

QUESTION 36
A custom poller has polled some results from nodes. Which of the following is a possible reason for NOT being able to show the polled results as charts on the Orion Web Console?

You did not set the poller to collect historical statistics

You must use Device Studio to build the poller

Charts are only supported by out-of-the-box pollers

The poller is not enabled and assigned to the devices

QUESTION 37
You need to change the polling method from ICMP to SNMP on 200 nodes you monitor with Orion. How would you best accomplish this?

Edit each individual node and change the polling method

Bulk select nodes in Manage Nodes and change the polling method

Use the Orion Polling Configuration tool to change polling methods

Unmanage all the nodes and remanage them choosing SNMP as the polling method

QUESTION 38
You created a Universal Device Poller (UnDP) but cannot find an OID in the MIB tree. How do you resolve this issue?

Restart the Universal Device Poller

Update the MIB database

Rediscover the node via Network Sonar Discovery

Add the node to NPM for monitoring

QUESTION 39
In which scenario is an agent the best solution?

If you cannot allow ICMP polling on your routers

If hosts in distributed networks have overlapping IP addresses

If the WMI ports are already in use on Linux

If Native GLX log file monitoring is required

QUESTION 40
You want to create an alert that notifies you when packet loss meets or exceeds 50%, but only for a select set of nodes in your network. How do you accomplish this?

Set the scope of the alert to only apply to nodes to be included in the alert

Set the alert trigger evaluation to evaluate nodes to be included in the alert

Create separate SWQL trigger condition for each node to be included in the alert

Set an alert limitation for the nodes to be included in the alert

QUESTION 41
How can you quickly generate a report in NPM to show the top 50 interfaces by percent utilization?

Create a web-based report and filter the data to restrict to the top 50 interfaces

Copy a similar default report and edit it for different time-frames

Copy a similar default report and edit it for the top 50 interfaces

Create an advanced SQL query report

QUESTION 42
Half of your objects in a nested map are down, but the top level map is up. What is the cause?

You set availability thresholds for devices to above 50%

You set availability thresholds for devices to below 50%

You set map status thresholds to above 50%

You set map status thresholds to below 50%

QUESTION 43
Your network has critical devices on the opposite side of a WAN link from you SolarWinds server. You do not want alerts about the devices if the router (name = “target”) that connects your SolarWinds server to the remote site is down. How do you configure Alert Suppression?

Suppress alert when all of the following apply: Node Name is equal to “target” / Interface Status is equal to “Warning”

Suppress alert when any of the following apply: Node Name is equal to “target” / Node Status is equal to “Warning”

Suppress alert when any of the following apply: Node Name is equal to “target” / Interface Status is equal to “Down”

Suppress alert when all of the following apply: Node Name is equal to “target” / Node Status is equal ta “Down”

QUESTION 44
Status, Average Response Time, and Packet Loss are the only node details data you can view for your switch A device. The node details of your identical switch B device show Status, Average Response Time, and Packet Loss and other statistics. How can you monitor the other statistics on switch A and not lose any historical data?

Delete switch A, and then add it again and this time choose “Most Devices: SNMP and ICMP” as the polling method

Edit the node properties of switch A and change the polling method to “Most Devices: SNMP and ICMP”

Edit the node properties of switch A and change the polling method to “Status Only: ICMP”

Edit the node properties of switch B and change the polling method to “Status Only: ICMP”

Add switch A again without deleting it first, and this time choose “Most Devices: SNMP and ICMP” as the polling method

QUESTION 45
Capacity planning is available for which metrics?

Up/Down, Packet Loss, and Latency

Response Time, Interface, and Volume Utilization

CPU, Memory, and Interface

Hardware Health

QUESTION 46
You want to create an Orion Map that shows the connections between your on-site devices and your servers in the Cloud. You can see the connections between all of the devices on site, but do not have visibility to the connections to your cloud servers.
How do you resolve this?

Manually configure connections between onsite and cloud resources in Orion Maps

Switch to SNMP polling for all devices to show the connections between on site and cloud resources

Increase the polling intervals between Orion and the cloud servers

Open additional firewall ports between the cloud servers and the on-site devices

QUESTION 47
You need to implement service level agreement (SLA) reporting for a new hosted data center service. Which SLA performance metric should you track?

Interface discards

Memory utilization

CPU utilization

Response time

QUESTION 48
You monitor three Cisco routers with NPM. NPM reports utilization statistics for two of the routers. NPM only shows Availability and Response Time statuses for the third router. Why do you not see utilization statistics on the third router?

SNMP is not configured correctly on the third node

The third node is monitored with WMI instead of SNMP

The third node is monitored with the NPM agent

The third node is monitored with SNMP instead of ICMP

QUESTION 49
You can make bulk changes, such as changing the polling method, to nodes.

TRUE

FALSE

QUESTION 50
How many agents does NPM require for Quality of Experience, NetPath, and system monitoring on the same Windows server?

QUESTION 51
Users report that NPM performance is slow when managing devices through the Orion Web Console. You verify the SNMP trapping is responsible for the poor performance. How do you resolve this issue?

Add the devices as managed nodes to cut down on the trap messages received

Point the devices to a trap manager and filter unwanted messages before forwarding remaining traps to the Orion Platform

Reduce the number of days SNMP messages are kept in the SolarWinds Trap Viewer

Add an Additional Web Server to handle the load of users accessing the NPM Orion Web Console

QUESTION 52
For any node you monitor, you can use Network Discovery to automatically add child volumes or interfaces for monitoring.

TRUE

FALSE

QUESTION 53
How can you ensure the trigger actions you set on an alert will work?

Use the Database Manager to trigger and test the alert

Simulate a performance interruption on a network device to test the alert trigger

Click Simulate on the assigned trigger action

Test the alert from within Alert View of the Web Console

QUESTION 54
You can use Device Studio to create pollers for CPU and memory?

TRUE

FALSE

QUESTION 55
You start a new job where NPM is already in use. As soon as you are added to the alert list, you begin receiving “high traffic utilization” alerts from a handful of interfaces.
When you check the alert, the traffic spike has ended. Your new colleagues advise you to ignore these alerts because the spikes rarely last for more than a couple of minutes and are only a concern if they last longer.
How should NPM be modified so you receive fewer false alerts?

Configure the alert so that it triggers only when traffic utilization remains high for a sustained period

Configure the alert so that it resets only when traffic utilization remains high fora sustained period

Increase the status polling frequency on the problematic interfaces

Increase the statistics polling frequency on the problematic interfaces

Loading …

SolarWinds SPM-NPM certification exam is a valuable credential for network professionals who want to demonstrate their expertise in network performance monitoring. SPM-NPM exam covers a broad range of topics related to network infrastructure, protocols, devices, and applications, and tests candidates’ ability to diagnose and troubleshoot performance issues at different layers of the network stack. With the right preparation and experience, candidates can achieve this certification and advance their careers in the dynamic and challenging field of network engineering and administration.

SolarWinds Network Performance Monitor (NPM) is a popular network monitoring tool that helps IT professionals identify and troubleshoot issues within their networks. The SolarWinds SPM-NPM (SolarWinds Network Performance Monitor) Certification Exam is designed to test an individual’s knowledge and expertise in using this tool to manage and monitor network performance. SolarWinds Network Performance Monitor (NPM) Exam certification exam is an essential qualification for IT professionals who want to demonstrate their proficiency in using SolarWinds NPM to monitor and manage network performance.

Dumps for Free SPM-NPM Practice Exam Questions: https://www.examboosts.com/SolarWinds/SPM-NPM-practice-exam-dumps.html