Free 2026 200-301 Dumps 100 Pass Guarantee With Latest Demo [Q667-Q690]

ExamBoosts February 15, 2026 200-301 > Cisco 0

Rate this post

Free 2026 200-301 Dumps 100 Pass Guarantee With Latest Demo

Prepare 200-301 Question Answers Free Update With 100% Exam Passing Guarantee [2026]

Cisco 200-301 exam is a critical certification exam for entry-level network engineers. 200-301 exam tests the candidate’s understanding of various networking concepts, including network access, IP connectivity, IP services, security fundamentals, and automation and programmability. Earning the CCNA certification demonstrates the candidate’s ability to work with Cisco technologies and solutions, making them a valuable asset to any organization.

NO.667 Refer to the exhibit.

An engineer is bringing up a new circuit to the MPLS provider on the Gi0/1 interface of Router1 The new circuit uses eBGP and teams the route to VLAN25 from the BGP path What s the expected behavior for the traffic flow for route 10.10.13.0/25?

Traffic to 10.10.13.0.25 is load balanced out of multiple interfaces

Route 10.10.13.0/25 is updated in the routing table as being learned from interface Gi0/1.

Traffic to 10.10.13.0/25 is asymmeteical

Route 10.10.13.0/25 learned via the GiO/0 interface remains in the routing table

NO.668 On which type of port can switches interconnect for multi-VLAN communication?

interface port

access port

switch port

trunk port

NO.669 Drag and drop to the characteristics of networking from the left onto the correct networking types on the right.

NO.670 Drag the descriptions of IP protocol transmissions from the left onto the IP traffic types on the right.

Explanation

TCP
* Sends tranmissions in sequence
4. Transmits packets individually
6. Uses a lower transmission rate to ensure relability
UDP
5. Uses a higher transmission rate to support latency-sensitive application
2. Transmissions include an 8-byte header
3. Transmits packets as a stream

NO.671 Refer to the exhibit.

The DHCP server is configured with a DHCP pool for each of the subnets represented. Which command must be configured on switch SW1 to allow DHCP clients on VLAN 10 to receive dynamic IP addresses from the DHCP server?

SW1(config-if)#ip helper-address 192.168.20.2

SW1(config-if)#ip helper-address 192.168.20.1

SW1(config-if)#ip helper-address 192.168.10.2

SW1(config-if)#ip helper-address 192.168.10.1

NO.672 Drag and drop the characteristic from the left onto the IPv6 address type on the right.

NO.673 Which mode must be used to configure EtherChannel between two switches without using a negotiation protocol?

auto

active

desirable
The Static Persistence (or “on” mode) bundles the links unconditionally and no negotiation protocol is used. In this mode, neither PAgP nor LACP packets are sent or received.

NO.674 Drag and drop the 802.11 wireless standards from the left onto the matching statements on the right

Explanation:

NO.675 Refer to the exhibit. What are the two steps an engineer must take to provide the highest encryption and authentication using domain credentials from LDAP?

Select PSK under Authentication Key Management

Select WPA+WPA2 on Layer 2 Security

Select Static-WEP + 802.1X on Layer 2 Security

Select WPA Policy with TKIP Encryption

Select 802.1X from under Authentication Key Management

NO.676 Refer to the exhibit.

What does router R1 use as its OSPF router-ID?

10.10.1.10

10.10.10.20

172.16.15.10

192.168.0.1

NO.677 Refer to the exhibit. The entire Marketing-SW1 MAC address table is shown here:

What does the switch do when PC-4 sends a frame to PC-1?

It performs a lookup in the MAC address table and discards the frame due to a missing entry.

It maps the Layer 2 MAC address to the Layer 3 IP address and forwards the frame.

It inserts the source MAC address and port into the table and forwards the frame to PC-1.

It floods the frame out of all ports except on the port where PC-1 is connected.

NO.678 An administrator must secure the WLC from receiving spoofed association requests. Which steps must be taken to configure the WLC to restrict the requests and force the user to wait 10 ms to retry an association request?

Enable Security Association Teardown Protection and set the SA Query timeout to 10

Enable MAC filtering and set the SA Query timeout to 10

Enable 802.1x Layer 2 security and set me Comeback timer to 10

Enable the Protected Management Frame service and set the Comeback timer to 10

NO.679 In which two ways does a password manager reduce the chance of a hacker stealing a user’s password?
(Choose two.)

It encourages users to create stronger passwords

It uses an internal firewall to protect the password repository from unauthorized access

It stores the password repository on the local workstation with built-in antivirus and anti-malware functionality

It automatically provides a second authentication factor that is unknown to the original user

It protects against keystroke logging on a compromised device or web site

Section: Security Fundamentals

NO.680 Refer to the exhibit.

A network administrator must permit SSH access to remotely manage routers in a network. The operations team resides on the 10.20.1.0/25 network. Which command will accomplish this task?

access-list 2699 permit udp 10.20.1.0 0.0.0.255

no access-list 2699 deny tcp any 10.20.1.0 0.0.0.127 eq 22

access-list 2699 permit tcp any 10.20.1.0 0.0.0.255 eq 22

no access-list 2699 deny ip any 10.20.1.0 0.0.0.255

Explanation
Note : Already a statement is there in last to allow SSH Traffic for network 10.20.1.0 0.0.0.127, but Second statement says deny ip any 10.20.1.0 0.0.0.255, so how it will work once it is denied. So the right answer is remove the — no access-list 2699 deny ip any 10.20.1.0 0.0.0.255.

NO.681 An engineer must configure a/30 subnet between two routers. Which usable IP address and subnet mask combination meets this criteria?

Option A

Option B

Option C

Option D

NO.682 Which two encoding methods are supported by REST APIs? (Choose two)

YAML

JSON

EBCDIC

SGML

XML

The Application Policy Infrastructure Controller (APIC) REST API is a programmatic interface that uses REST architecture. The API accepts and returns HTTP (not enabled by default) or HTTPS messages that contain JavaScript Object Notation (JSON) or Extensible Markup Language (XML) documents.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/2- x/rest_cfg/2_1_x/ b_Cisco_APIC_REST_API_Configuration_Guide/ b_Cisco_APIC_REST_API_Configuration_Guide_chapter_01.html

NO.683 Drag and drop the descriptions of AAA services from the left onto the corresponding services on the right.

Explanation:

NO.684

Refer to the exhibit. An engineer is asked to confere router R1 so that it forms an OSPF single-area neighbor relationship with R2. Which command sequence must be implemented to configure the router?

Option A

Option B

Option C

Option D

NO.685 Refer to the exhibit.

What is represented by the word “switch” in line 2 of the JSON schema?

array

key

value

object

NO.686 Refer to the exhibit.

Which switch becomes the root bridge?

NO.687 Refer to the exhibit.

What does router R1 use as its OSPF router-ID?

10.10.1.10

10.10.10.20

172.16.15.10

192.168.0.1
OSPF uses the following criteria to select the router ID: 1. Manual configuration of the router ID (via the “router-id x.x.x.x” command under OSPF router configuration mode). 2. Highest IP address on a loopback interface. 3. Highest IP address on a non-loopback and active (no shutdown) interface.

NO.688 which command can you enter to troubleshoot the failure of address assignment?

show ip dhcp database

show ip dhcp pool

show ip dhcp import

show ip dhcp server statistics

NO.689 Configure IPv4 and IPv6 connectivity between two routers. For IPv4, use a /28 network from the 192.168.1.0/24 private range. For IPv6, use the first /64 subnet from the 2001:0db8:aaaa::/48 subnet.
1. Using Ethernet0/1 on routers R1 and R2, configure the next usable/28 from the 192.168.1.0/24 range. The network 192.168.1.0/28 is unavailable.
2. For the IPv4 /28 subnet, router R1 must be configured with the first usable host address.
3. For the IPv4 /28 subnet, router R2 must be configured with the last usable host address.
4. For the IPv6 /64 subnet, configure the routers with the IP addressing provided from the topology.
5. A ping must work between the routers on the IPv4 and IPv6 address ranges.

See the Explanation below

Answer as below configuration:
on R1
config terminal
ipv6 unicast-routing
inter eth0/1
ip addre 192.168.1.1 255.255.255.240
ipv6 addre 2001:db8:aaaa::1/64
not shut
end
copy running start
on R2
config terminal
ipv6 unicast-routing
inter eth0/1
ip address 192.168.1.14 255.255.255.240
ipv6 address 2001:db8:aaaa::2/64
not shut
end
copy running start
———————
for test from R1
ping ipv6 2001:db8:aaaa::1
for test from R2
ping ipv6 2001:db8:aaaa::2

NO.690 Drag and drop the characteristic from the left onto the IPv6 address type on the right.