2022 Valid 200-301 test answers & Cisco Exam PDF [Q165-Q180]

ExamBoosts April 19, 2022 200-301 > Cisco 0

Rate this post

2022 Valid 200-301 test answers & Cisco Exam PDF

Free Cisco 200-301 Exam Questions and Answer from Training Expert ExamBoosts

Cisco CCNA 200-301 Practice Test Questions, Cisco CCNA 200-301 Exam Practice Test Questions

The Cisco 200-301 exam is a single test required for obtaining the Cisco Certified Network Associate (CCNA) certification. This certificate assists the professionals in validating their knowledge and skills in the IT fundamentals and serves as a springboard for launching their careers in the field.

NO.165 Drag and drop the AAA functions from the left onto the correct AAA services on the right

NO.166 A port security violation has occurred on a switch port due to the maximum MAC address count being exceeded. Which command must be configured to increment the security-violation count and forward an SNMP trap?

switchport port-security vilation access

switchport port-security vilation protect

switchport port-security vilation restrict

switchport port-security vilation shutdown

Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/25ew/configuration/guide/conf/port_sec.h

NO.167 R1 has learned route 192.168.12.0/24 via IS-IS, OSPF, RIP and Internal EIGRP Under normal operating conditions, which routing protocol is installed in the routing table?

IS-IS

RIP

Internal EIGRP

OSPF

With the same route (prefix), the router will choose the routing protocol with lowest Administrative Distance (AD) to install into the routing table. The AD of Internal EIGRP (90) is lowest so it would be chosen. The table below lists the ADs of popular routing protocols.

Note: The AD of IS-IS is 115. The “EIGRP” in the table above is “Internal EIGRP”. The AD of
“External EIGRP” is 170. An EIGRP external route is a route that was redistributed into EIGRP.

NO.168 What is recommended for the wireless infrastructure design of an organization?

group access points together to increase throughput on a given channel

configure the first three access points are configured to use Channels 1, 6, and 11

include a least two access points on nonoverlapping channels to support load balancing

assign physically adjacent access points to the same Wi-Fi channel

NO.169 Which output displays a JSON data representation?

Option A

Option B

Option C

Option D

NO.170 Refer to the exhibit. Which type of configuration is represented in the output?

Ansible

JSON

Chef

Puppet

NO.171 Refer to the graphic. R1 is unable to establish an OSPF neighbor relationship with R3.
What are possible reasons for this problem? (Choose two.)

All of the routers need to be configured for backbone Area 1.

R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.

A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.

The hello and dead interval timers are not set to the same values on R1 and R3.

EIGRP is also configured on these routers with a lower administrative distance.

R1 and R3 are configured in different areas.

This question is to examine the conditions for OSPF to create neighborhood. So as to make the two routers become neighbors, each router must be matched with the following items:
1. The area ID and its types;
2. Hello and failure time interval timer;
3. OSPF Password (Optional);

NO.172 Which configuration command can u apply to a HSRP router so that its local interface becomes active if all other routers in the group fail?

no additional config is required

standby 1 track ethernet

standby 1 preempt

standby 1 priority 250

Simply because that will be the default behavior routers would follow in the event all other routers in the HSRP group fail, then it would not keep attributes such as priority or preemption. What preemption does in summary is to make sure that the configured Priority on all routers within the same HSRP group is always respected. That is, if R1 is configured on the HSRP group with a priority of 150 but he stands as active since all other routers currently subscribed to that group have a priority 150, then will router will preempt the current active router and will take over hence becoming the new active router.
With preemption disabled, the new router does not preempt the current active router, unless routers in the group have to renegotiate their roles based on each router’s priority at the time of negotiation.

NO.173 A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented?
(Choose two)

runts

giants

frame

CRC

input errors

Explanation
Whenever the physical transmission has problems, the receiving device might receive a frame whose bits have changed values. These frames do not pass the error detection logic as implemented in the FCS field in the Ethernet trailer. The receiving device discards the frame and counts it as some kind of input error.
Cisco switches list this error as a CRC error. Cyclic redundancy check (CRC) is a term related to how the FCS math detects an error.
The “input errors” includes runts, giants, no buffer, CRC, frame, overrun, and ignored counts.
The output below show the interface counters with the “show interface s0/0/0” command:

NO.174 I
A Cisco IP phone receives untagged data traffic from an attached PC Which action is taken by the phone?

It allows the traffic to pass through unchanged

It drops the traffic

It tags the traffic with the default VLAN

It tags the traffic with the native VLAN

Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/vlan/configuration_guid Untagged traffic from the device attached to the Cisco IP Phone passes through the phone unchanged, regardless of the trust state of the access port on the phone.

NO.175 What is the benefit of configuring PortFast on an interface?

After the cable is connected, the interface uses the fastest speed setting available for that cable type

After the cable is connected, the interface is available faster to send and receive user data

The frames entering the interface are marked with higher priority and then processed faster by a switch.

Real-time voice and video frames entering the interface are processed faster

NO.176 Which technology must be implemented to configure network device monitoring with the highest security?

IP SLA

syslog

NetFlow

SNMPv3

Section: Security Fundamentals

NO.177 Refer to the exhibit.

Which two facts can you determine from the EIGRP topology table? (Choose two)

If a route has more than one successor, only one route is injected into the routing table.

The FD 28416 for route 10.242. 0.148 is also the metric for the routing table

The variance command must have been issued to allow route 10.85.184.0 to have two Successors.

The reported distance value is greater than the feasible distance

All successors are injecting into the routing table

NO.178

Refer to the exhibit. Which route does R1 select for traffic that is destined to 192.168.16.2?

192.168.16.0/21

192.168.16.0/24

192.168.26.0/26

192.168.16.0/27

Section: IP Connectivity

NO.179 Which IPsec security protocol should be used when confidentiality is required?

MD5

PSK

ESP

NO.180 Which unified access point mode continues to serve wireless clients after losing connectivity to the Cisco Wireless LAN Controller?

local

mesh

flexconnect

sniffer

Section: Network Access
Explanation:
In previous releases, whenever a FlexConnect access point disassociates from a controller, it moves to the standalone mode. The clients that are centrally switched are disassociated. However, the FlexConnect access point continues to serve locally switched clients. When the FlexConnect access point rejoins the controller (or a standby controller), all clients are disconnected and are authenticated again. This functionality has been enhanced and the connection between the clients and the FlexConnect access points are maintained intact and the clients experience seamless connectivity. When both the access point and the controller have the same configuration, the connection between the clients and APs is maintained.
Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/ b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010001101.html

Loading …