[Sep 09, 2024] Fortinet NSE6_FSW-7.2 Real Exam Questions and Answers FREE [Q17-Q36]

Diesen Beitrag bewerten

[Sep 09, 2024] Fortinet NSE6_FSW-7.2 Real Exam Questions and Answers FREE

Pass Fortinet NSE6_FSW-7.2 Exam Info and Free Practice Test

The Fortinet NSE 6 – FortiSwitch 7.2 certification exam covers a range of topics, including VLANs, STP, multicast, link aggregation, FortiSwitch management, and FortiLink. NSE6_FSW-7.2 exam also covers advanced topics such as FortiSwitch security features, FortiSwitch troubleshooting, and FortiSwitch integration with other Fortinet products. NSE6_FSW-7.2 exam is a comprehensive test of a candidate’s knowledge and skills in FortiSwitch 7.2.

FRAGE 17
Which statement about 802.1X security profiles using MAC-based authentication mode is true?

FortiSwitch allows connectivity to all hosts connected to a port, if one host is authenticated.

FortiSwitch can grant each device a different access level based on the credentials provided

FortiSwitch performs faster when using this security mode on the ports.

FortiSwitch must communicate with the RADIUS server to authenticate devices

FRAGE 18
What are two ways in which automatic MAC address quarantine works on FortiSwitch? (Choose two.)

FortiSwitch supports only by VLAN quarantine mode.

FortiGate applies the quarantine-related configuration only on FortiGate.

FortiAnalyzer with a threat detection services license is required.

MAC address quarantine can be enabled through the FortiGate CLI only.

FRAGE 19
Siehe dazu die Exponate.

Port1 and port2 are the only ports configured with the same native VLAN 10.
What are two reasons that can trigger port1 to shut down? (Choose two.)

port1 was shut down by loop guard protection.

STP triggered a loop and applied loop guard protection on port1.

An endpoint sent a BPDU on port1 that it received from another interface.

Loop guard frame sourced from port 1 was received on port 1.

FRAGE 20
Ausstellen.

LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)

Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group

Switch 3 and Switch 4 uplinks are treated as single interfaces.

Switch 3 and switch 4 are seen as one MCLAG switch client

Switch 1 and Switch 2 both seen as one single switch.

FRAGE 21
Which drop policy mode, if assigned to a congested port, will drop incoming packets until there is no congestion on the egress port?

Tail-drop mode

Weighted round robin mode.

Random early detection mode

Strict mode

FRAGE 22
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

All ports have auto-discovery enabled by default.

No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

The last four switch ports on FortiSwitch have auto-discovery enabled by default.

FRAGE 23
Which two statements about managing a FortiSwitch stack on FortiGate are true? (Choose two.)

A FortiLink interface must be enabled on FortiGate.

The switch controller feature must be enabled on FortiGate.

Only a hardware-based FortiGate can manage a FortiSwitch stack.

FortiSwitch must be operating in standalone mode before authorization.

FRAGE 24
Which two statements about the FortiLink authorization process are true? (Choose two.)

The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.

FortiSwitch requires a reboot to complete the authorization process.

A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.

FortiLink authorization sets the FortiSwitch management mode to FortiLink.

FRAGE 25
Siehe dazu die Abbildung.

Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)

FortiSwitch is sending FortiLink heartbeats to FortiGate.

FortiSwitch is discovered and authorized by FortiGate.

FortiSwitch is in a waiting state to join the stack group on FortiGate.

FortiSwitch is ready to push its new hostname to FortiGate.

FRAGE 26
Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

FRAGE 27
Siehe dazu die Abbildung.

What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)

Maximum value to accept clients DHCP request is configured as per DHCP server range.

FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.

DHCP clients that are trusted by DHCP snooping configured is only one.

Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.

FRAGE 28
Which two statements about DHCP snooping enabled on a FortiSwitch VLAN are true? (Choose two.)

Enabling DHCP snooping on a FortiSwitch VLAN ensures requests and replies are seen by all DHCP servers.

switch-controller-dhcp-snooping-verify-mac verifies the destination MAC address to protect against DHCP exhaustion attacks.

By default, all FortiSwitch ports are set to forward client DHCP requests to untrusted ports.

Settings related to DHCP option 82 are only configurable through the CLI

FRAGE 29
How does FortiSwitch perform actions on ingress and egress traffic using the access control list (ACL)?

Only high-end FortiSwitch models support ACL.

ACL can be used only at the prelookup stage in the traffic processing pipeline.

Classifiers enable matching traffic based only on the VLAN ID.

FortiSwitch checks ACL policies only from top to bottom.

FRAGE 30
Which statement about using MAC, IP, and protocol-based VLANs on FortiSwitch is true?

lt is a scalable and secure solution in comparison to other Layer 2 security measures.

FortiSwitch uses only the Ethernet type to assign traffic to VLANs.

It provides benefits that can be obtained when using 802.1X authentication.

Endpoints are required to use the same FortiSwitch port to remain members of the VLAN.

FRAGE 31
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

The handshake process timed out before FortiSwitch responded.

DTLS client hello had the incorrect pre-shared key.

The CAPWAP tunnel failed to come up due to a mismatch in time.

FortiSwitch has disabled FortiLink and is only managed as a standalone.

FRAGE 32
Siehe dazu die Exponate.

You are asked to ensure that managed FortiSwitch devices are reachable by other devices, such as SNMP and other management tools across your network.
Which setting must you configure to ensure traffic from other devices in the network reaches FortiSwitch?

Select a specific default gateway provided to FortiSwitch as an upstream device.

Change the FortiLink interface IP address and DHCP server address range.

Recreate the FortiLink interface with a nonaggregate setting.

Enable NAC settings to select the onboarding VLAN.

FRAGE 33
Which statement about the configuration of VLANs on a managed FortiSwitch port is true?

Untagged VLANs must be part of the allowed VLANs: ingress and egress.

FortiSwitch VLAN interfaces are created only when FortiSwitch is managed by Forti-Gate.

The native VLAN is implicitly part of the allowed VLAN on the port.

Allowed VLANS expand the collision domain to the port.

FRAGE 34
Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?

Enable the IGMP flood setting on the static port for all multicast groups.

Enable the IGMP flood reports setting on the mRouter port.

Enable IGMP snooping proxy.

Enable IGMP flood unknown multicast traffic on the global setting.

FRAGE 35
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?

Use a migration tool based on Python script to convert the configuration.

Enable the FortiLink setting on FortiSwitch before the authorization process.

FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.

FRAGE 36
Ausstellen.

The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?